Home
About Us
Company Profile
Honor
Equipment
Products
Vacuum box helium leak detection and recovery integrated equipment
Helium recovery and purification equipment
Laboratory analytical instruments
Helium mass spectrometer leak detector
Partners
Blog
Company News
Industry News
Join Us
Contact Us
中文版
English
Company Information
Knowledge
Application Notes for High-Purity Helium: A Gas Purification Equipment Manufacturer Tells You!
The applications of gases are becoming increasingly widespread, appearing in both industrial settings and our daily lives. High-purity helium gas should be used with a pressure reducer such as the YQY-12 or 152IN-125 before use. Before use, check for leaks in the gas pipeline with soapy water to ensure that the gas pipeline is leak-free. Ensure that the helium does not leak and that the workplace is well-ventilated.
11
2025
/
03
Issues to Note When Using a Helium Leak Detector with the Suction Gun Method
Helium leak detection using a suction gun (positive pressure method). When using pure helium, a helium recovery device can be used for reuse to reduce costs. Alternatively, a helium gas mixture with a concentration of no less than 5-10% can be used and directly discharged into the atmosphere after use. Pay attention to the concentration of helium in the surrounding environment and the airflow, as this will affect the detection accuracy of the suction gun method.
Why can helium be used as a leak detection gas?
First, because helium's outermost electron shell contains only two electrons, and helium only has one electron shell, this means it has achieved a stable structure. Therefore, helium's chemical properties are relatively stable, making it resistant to reactions and explosions. In some valuable equipment such as airplanes and spaceships, helium is preferred as a leak detection gas. However, helium is scarce in nature and relatively expensive, so to save costs, some companies choose a hydrogen-nitrogen mixture as a leak detection gas, or use nitrogen directly.
The leak detection role of helium in semiconductors
To prevent the performance degradation of semiconductor devices, integrated circuits, and other components due to surface contamination from moisture and other impurities, sealing with a shell is necessary. However, small holes that are difficult to detect with the naked eye often occur at the sealing points of the shell or at the lead connection points due to various reasons. Therefore, after the component is packaged, certain methods are required to detect the presence or absence of these small holes. Helium leak detection uses helium gas to check for small holes in the shell of the electronic component package. Because helium atoms are very small and easily pass through small holes into the shell, this detection method can detect very small holes (i.e., it can detect holes with a leak rate of approximately 10−11~10−12cm3/sec), with a sensitivity comparable to that of radioactive leak detection, but simpler than radioactive leak detection. Helium leak detection test method: First, place the packaged components in a container filled with helium gas and pressurize it, allowing the helium gas to enter the shell through the small holes; then take it out and use compressed air to blow away the residual helium gas on the shell surface; then use a mass spectrometer to detect the helium gas leaking from the shell surface.
Detection principles, advantages, disadvantages, and detection standards of four common helium mass spectrometry leak detection methods
When leak detection is performed using the vacuum method, an auxiliary vacuum pump or leak detector is used to evacuate the internal sealed chamber of the product under test. Helium gas is applied to the outer surface of the product using a helium hood or spraying method. When there is a leak hole on the surface of the product under test, the helium gas will pass through the leak hole and Enter the inside of the product under test, and then Enter the helium mass spectrometer leak detector, so as to measure the leakage amount of the product under test. According to the different methods of applying leaked gas, the vacuum method can also be divided into vacuum spraying method and vacuum helium hood method. The vacuum spraying method uses a spray gun to spray helium gas onto the outer surface of the product under test, which can accurately locate the leak hole; the vacuum helium hood method uses a helium hood with a certain sealing function to cover the entire product under test, and fills the hood with a certain concentration of helium gas, which can measure the total leakage rate of the product under test.
10
Gas purification classification and production process
The main production processes of specialty gases include gas synthesis, gas purification, gas mixing, cylinder treatment, gas filling, and gas analysis and testing. Gas synthesis is the process of obtaining crude gas products through chemical reactions under specific conditions of pressure, temperature, and catalysts. Gas purification is the process of refining crude products into higher-purity products through methods such as distillation and adsorption.